Bolt Motorcycle Hardware Products     KTM/Husqvarna/Husaberg Bolt Kits     Chain Adjuster Blocks     KTM/HQV/Berg Rotor Bolts     Valve Stem Grommets/Caps Kit    CR/CRF Track Pack Bolt Kit (Closeout)     ATV Bolt Kits (Closeout)     YZ/WR Bodywork Fastener Kit (Closeout)  
 

Hub-Savers Double Locked Sprocket Fastening Kit

Designed to fit all Japanese and most European dirt bikes. This kit includes six class 10.9 silver zinc plated steel sprocket bolts with factory style metal-locking or "Fuji" nuts. Each sprocket bolt has medium strength threadlock patches applied for a double-lock. Threadlock liquifies and anaerobically seals when the bolt is tightened. This kit also includes an 8mm tool insert for socket wrenches. Proudly produced in the USA.
Important Installation Information
 
    Cost Add To Cart
 





Euro Hub-Savers Kit - Silver Finish
Fits KTM, Husqvarna and Husaberg models with T45 26mm in length sprocket bolts.
---
This kit includes six class 10.9 zinc plated Euro Style steel sprocket bolts with factory style class 10.9 Fuji metal-locking nuts and washers. The bolts feature a factory style T45 Torx Socket Head. Each sprocket bolt has medium strength thread lock patches pre-applied, which liquefies and anaerobically seals when the bolt is tightened for a double-lock.
BO-SP-EURO


$9.99
MSRP $10.99
 
 




Hub-Savers Kit - Silver Finish
30mm sprocket bolts with Fuji lock flange nuts and washers. Fits all full size off-road motorcycles.
---
Double Locked Sprocket Fastening Kit - includes six class 10.9 silver zinc plated steel sprocket bolts with factory style metal-locking or "Fuji" nuts.
BO-SP-BOLT


$9.99
MSRP $10.99
 
 




Hub-Savers Kit - Black Finish
30mm sprocket bolts with Fuji lock flange nuts and washers. Fits all full size off-road motorcycles.
---
Double Locked Sprocket Fastening Kit - includes six class 10.9 silver zinc plated steel sprocket bolts with factory style metal-locking or "Fuji" nuts.
BO-SP-BOLT-BK


$9.99
MSRP $10.99
 





  Hub-Savers Sprocket Bolts with Installation Instructions

 
 

 
Fits all Japanese and most European dirt bikes. This kit includes six class 10.9 zinc plated steel sprocket bolts with factory style class 10.9 Fuji metal-locking nuts and washers. Each sprocket bolt has medium strength thread lock patches pre-applied, which liquefies and anaerobically seals when the bolt is tightened for a double-lock. This kit also includes an 8mm socket tool insert for socket wrenches.

Important installation information:
Hub-Savers are the strongest, most complete sprocket fasteners available and have been developed and tested at the professional level in both motocross and off-road applications. Sprocket bolts are a critical fastener and must be installed properly to ensure your safety and to avoid damaging your machine. To insure long and reliable use of these quality fasteners:

  First clean and inspect your hub. If the hub is damaged or if the mounting holes are oval, the hub must
  Use the included Allen insert in an 8mm socket wrench to install the sprocket bolts.
  Refer to your owner's manual for the proper torque (typically 25 ft lbs), take the torque reading on the nut side.
Never over-tighten sprocket bolts!

If your sprocket bolts become loose, they must be replaced! Sprocket bolts become loose only under extreme stress, an indication that either they were installed improperly or there is a problem with the drive line. Check the drive line for bent chain guides, bad wheel alignment, damaged mounting holes on the hub, etc. Properly tightened sprocket bolts on properly functioning drive lines will remain tight indefinitely.

Bolt hardware meets or exceeds OEM specs. Proudly designed and assembled in the USA with components from the USA and Taiwan.


  
Euro Hub-Savers: 26mm Sprocket Bolts (BO-SP-EURO) Silver Hub-Savers: 30mm Sprocket Bolts (BO-SP-BOLT)


 
Black Hub-Savers: 30mm Sprocket Bolts (BO-SP-BOLT-BK)